| |
| DYNAMIX HP-52/SW |
| HomeCNA3.1 Coax
modem (192Mbps) with WiFi 11b/g/n |
|
|
View Larger Picture
|
This equipment including guaranteed quality of service (QoS), low cost, robust performance, and the ability to operate over coax cables.
DYNAMIX HP-52/SW enables You to set-up your Private Network at Home with your Existing Coaxial Cable,
with Wi-Fi extension. No additional Network wiring is necessary. You may just Find a Coax Connector in the wall, put the coaxial plug into the connector, you can then be ready to access the broadband Internet
(at connection to HomeCNA3.1 Coax MDU Master Bridge - DYNAMIX HP- 52/M). No extra utility is needed. No setting, just link. Simply Plug & Play.
Via the RJ-45 Ethernet Ports, You can connect DYNAMIX HP- 52/SW with the Ethernet - Interfaced Devices such as STB, Camera Server, PC or Switch/Hub.
The High speed of 192Mbps will bring you to enjoy the “video-on-demand” or “multimedia-on-demand”
services.
Availability 11b/g/n Wi-Fi interface can significantly extend the functionality of the device by connecting it to other devices with a wireless interface.
To connect an analog telephone and the implementation of VoIP calls and receive calls over the Internet or VPN network in a series of DYNAMIX HP-52 / SW is a special model that supports FXS interface - DYNAMIX HP-52 / SW FXS. |
 User's manual
User's
guide
|
|
|
|
| • |
HCNA Coax Port as Home Network Backbone by Using Existing Coaxial Cable,
support Wi-Fi
(MIMO 2x2 11b/g/n Wi-Fi Access Point) |
| • |
HCNA up to 192Mbps PHY Rate as Distribution Backbone over Coax |
| • |
Two 10/100M Fast Ethernet Ports |
| • |
Up to 65dB Attenuation on Coax Network |
| • |
Filter Built-in to Eliminate Noise from TV |
| • |
QoS Priority and Mapping Support |
| • |
Queuing Schemes for Variant QoS Demand |
| • |
TagVLAN Configuration |
| • |
Service and Bandwidth Control |
| • |
IGMP Snooping Control |
| • |
Intelligence for Carrier IPTV Service |
| • |
The model supports FXS interface - DYNAMIX HP-52 / SW FXS |
 Back to Top
|
|
|
|
|
| Networks standards |
| | HomePNA 3.1 over Coaxial Cable (HCNA) |
| | IEEE 802.3 10M Ethernet |
| | IEEE 802.3u 100M Fast Ethernet |
| | IEEE 802.3x Flow Control |
| | IEEE 802.11 b/g/n Wi-Fi |
| Connectors |
| | Ethernet : Two RJ-45 Ports |
| | HCNA : Two F-Type Female Coax Connectors, One for HCNA, the Other One for TV |
| | Telephone: One RJ11 Female
(DYNAMIX HP-52/SW FXS) |
| Voice over IP
(FXS model) |
| | SIP Protocol, G.711 and Low Bit Rate Codec |
| | Supplementary
Service: Call Waiting, Call Hold, Call Transfer, Call
Forward, 3-Way Conference |
| | Auto Provisioning Support |
| Transmission Power/Spectrum |
| | 15 +/- 1 dBm |
| | 12 - 44MHz |
| Transmission Range and Distance |
| | Data Rate Up to
192Mbps |
| | Up to 65dB Attenuation |
| Fast Ethernet Interface |
| | 10/100Mbps Auto Negotiation |
| | MDI/MDI-X Auto Crossover |
| Wi-Fi Interface |
| | MIMO 2x2 Wi-Fi IEEE802.11b/g/n |
| | Security: WEP,
WPA/WPA2, WPA/WPA2 with PSK |
| Management
(via DYNAMIX HP-52/M) |
| | DHCP Support: Option 82 and Snooping |
| | Auto Configuration Support |
| | Priority Based on 802.1p,
TOS, TCP/UDP Port |
| | 802.1Q TagVLAN Support |
| | Diagnosis of HCNA
Interface, and Noise Spectrum Analyzer Built-in |
| | Firmware Upgrade |
| | Bandwidth Control |
| | IGMP v2 Snooping Control |
| | Endpoint Ethernet Statistics and Status |
| Indicators |
| | "Power" LED |
| | HCNA "Link/Activity" LED |
| | Ethernet “Link/Activity” LED x 2 |
| | Wi-Fi "Link/Activity" |
| | Phone: “Register” LED and Call Status LED
( DYNAMIX HP-52/SW FXS) |
| Power Requirement |
| | External Power Supply :
12VDC |
| | Power Consumption <
8Watt |
| EMI/EMC |
| | Comply with VCCI and FCC Part 15 |
| | Comply with CE |
| Environmental Conditions |
| | Operating Temperature : 0 C ~
50 C (32 F ~ 104 F) |
| | Storage Temperature : -10 C ~ 65 C (14 F ~ 149 F) |
| | Operating Humidity : 10% ~ 95%, Non-Condensing |
| | Physical Dimension:
130mm (W) x 95mm (D) x 32mm (H) |
| | Weight: about
200 g |
|
|
Back to Top
|
|
|
|
|
|
| DYNAMIX HP- 52/SW |
HomeCNA3.1 Coax modem (192Mbps) with WiFi 11b/g/n |
| DYNAMIX HP- 52/SW FXS |
HomeCNA3.1 Coax modem (192Mbps) with WiFi 11b/g/n
and FXS port |
|
|
Back to Top |
|
|
Also see the products of this group:
|
|
EoC (Ethernet over Coaxial Cable)
|
|
DYNAMIX HP- 53/M EoC Coax MDU Master Bridge (700/350Mbps), Indoor
|
|
DYNAMIX HP- 53/M Outdoor
EoC Coax MDU Master Bridge (700/350Mbps), Outdoor
|
|
DYNAMIX HP-53/S EoC Coax MDU Data Endpoint
(700/350Mbps), 2 ports 10/100 Base-TX
|
|
DYNAMIX HP-53/SW EoC Coax MDU Endpoint with WiFi 11b/g/n (700/350Mbps), 2 ports 10/100 Base-TX
|
|
DYNAMIX HP-53/S FXS EoC Coax MDU Voice Endpoint (700/350Mbps), 2 ports 10/100 Base-TX,
1 port FXS
|
|
DYNAMIX HP-53/SW FXS
EoC Coax MDU Voice Endpoint with WiFi
11b/g/n (700/350Mbps), 2 ports 10/100 Base-TX, 1 port FXS
|
|
HomePNA 3.1 adapter, router
|
|
DYNAMIX HP-30/S(FE)
HomePNA 3.1 (192 Mbps) - Ethernet adapter (2 ports 10/100
Base-TX)
|
|
HomeCNA 3.1 Bridge, adapter
|
|
DYNAMIX HP-33/S(GE) HCNA (HomePNA 3.1 over Coax) to Gigabit Ethernet Bridge {256Mbps}
|
|
DYNAMIX HP- 52/M
HomeCNA3.1 Coax MDU Master Bridge
(2 ports 10/100/1000 Base-TX) (192Mbps)
|
|
DYNAMIX HP- 52/S HomeCNA3.1 Coax
modem (2 ports 10/100 Base-TX) (192Mbps)
|
|
DYNAMIX HP- 52/S FXS HomeCNA3.1 Coax
modem (2 ports 10/100 Base-TX) (192Mbps) with FXS port
|
|
DYNAMIX HP- 52/SW HomeCNA3.1 Coax
modem (2 ports 10/100 Base-TX) (192Mbps) with WiFi 11b/g/n
|
|
DYNAMIX HP- 52/SW FXS HomeCNA3.1 Coax
modem (2 ports 10/100 Base-TX) (192Mbps) with WiFi 11b/g/n and FXS port
|
|
|
