FiberMix 907-EV35 Standalone 10BaseT to V.35 Converter

FiberMix 907-EV35

Standalone 10BaseT to V.35 Converter

Specification | Front panel | Application | Ordering information

FiberMix 907 offer easy connections of LANs/MANs and shall be used in pair. With this solution, standard DDN systems may be fully and extensively utilized for local LANs/MANs. They can be integrated easily with previously set up networks. It is a flexible solution with a broad functional range, allowing for the conversion of Ethernet-formatted data into standard formats at data transmission rates within range of V.35. The rate range is up to 8Mbps. Features like auto-negotiation and auto-crossing guarantee easy installation and low maintenance efforts.

User's manual
300 Kb

Quick start

•

Cost-effective Ethernet to V.35 conversion

•

Connect LANs/MANs via existing TDM networks

•

Available as slide-in module or as standalone unit

•

SNMP management

•

Supports capability of V.35 signals loss alarm and faults reported to Switch

•

Integrated SDRAM 64M memory can mitigate data congestion and reduce packets loss

•

Integrated MAC address list has address filtering capability to improve efficiency of V.35 link

•

FiberMix 907 and FiberMix 908 offer easy connections of LANs/MANs and shall be used in pair. With this solution, standard DDN systems may be fully and extensively utilized for local LANs/ MANs. They can be integrated easily with previously set up networks

•

It is a flexible solution with a broad functional range, allowing for the conversion of Ethernet-formatted data into standard formats at data transmission rates within range of V. 35. The rate range is up to 8Mbps. Features like auto-negotiation and auto-crossing guarantee easy installation and low maintenance efforts.

V.35 Interface
	Physical Characteristics: Compliant to V.35 interface standard
	Interface Type: HDB26 female connector (26-pin female connector)
	Working Mode: DTE Interface
	Bit Rate: Dependent on DCE, up to 8Mbps

Ethernet Interface
	10BaseTx Ethernet port (RJ45) Compliant to IEEE 802.3 standard Full/Half duplex auto-negotiation
	Standalone units provide built-in power supply

Dimensions
	standalone unit: 157(W)32(H)120(D) (mm)
	modular unit: 91(W)25(H)155(D) (mm)

Power Supply
	115/230VAC -48DC
	Power Consumption: 3W

Environment
	0~60 degrees Centigrade operating less than 90% humidity (25 degrees Centigrade)

Compliance
	CE certification

Front panel FiberMix 907-EV35 Standalone 10BaseT to V.35 Converter

Application FiberMix 907-EV35 Standalone 10BaseT to V.35 Converter

Point-to-point Ethernet extension over DDN, enables 10BaseT Ethernet equipment to utilize V.35 transmission link, by converting Ethernet frames into V.35 bit stream. Provides DDN dedicated network for department of finance, government and education, etc. Compact standalone unit, saving space. The application provides a costeffective solution for carriers.

FiberMix 907-EV35

Standalone, 10Base-T to V.35 interface converter, AC 115V or 230V/DC –48V

Also see the products of this group:

G.703 E1-U/ FE1/ FE1-A Single Port E1 and Fractional E1 Access Unit

FiberMix 903-V35FE1 V.35 to E1 fractional Interface Converter

FiberMix 904-V35FE1 Module, V.35 to transparent or fractional E1 interface converter, SNMP-management

FiberMix 907-EV35 Standalone 10BaseT to V.35 Converter

FiberMix 905-EE1 Standalone 10Mbps on Transparent or Fractional E1 Converter

FiberMix 001-1 1-slot Chassis

FiberMix 002-4 4-slot Chassis (managed)

FiberMix 002-16 16-slot Modular Converter Chassis with SNMP Management

FiberMix 001-NMS1 Master Management Agent Module for 3U Chassis

FiberMix 001-NMS2 Slave Management Module for 3U Chassis

FiberMix 004-16NMS1 Master Management Agent Module for 10U Chassis

FiberMix 004-16NMS2 Slave Management Module for 10U Chassis

FiberMix 802-60 Module, 2 E1 channels optical multiplexer, SNMP-management

FiberMix 803-120 Standalone, 4 E1 channels optical multiplexer, remote SNMP-management, SSF, Dual WL, 1310nmTX 1550nmRX, 19” 1U chassis, AC 115V or 230V, DC – 48V

FiberMix 805-120B Standalone, 4 E1 channels optical multiplexer, remote SNMP-management, SSF, Dual WL, 1550nmTX 1310nmRX, 19” 1U chassis, AC 115V or 230V, DC –48V

FiberMix 804-60B Module, 2 E1 channels optical multiplexer, SNMP-management, SSF, Dual WL, 1310nmTX 1550nmRX

FiberMix 806-60B Module, 2 E1 channels optical multiplexer, SNMP-management, SSF, Dual WL, 1550nmTX 1310nmRX

FiberMix 803-480B Standalone, 16 E1 channels optical multiplexer, SSF, Dual WL, 1310nmTX 1550nmRX, 19” 1U chassis, AC 115V or 230V/DC –48V

FiberMix 805-480B Standalone, 16 E1 channels optical multiplexer, SSF, Dual WL, 1550nmTX 1310nmRX, 19” 1U chassis, AC 115V or 230V/DC –48V

FiberMix 805-240B Standalone, 8 E1 channels optical multiplexer, remote SNMP-management SSF, Dual WL, 1550nmTX 1310nmRX, 19” 1U chassis, AC 115V or 230V/DC –48V

FiberMix 2304-120 Standalone, 4 E1 channels optical multiplexer, 4 10/100 RJ45, remote SNMP-management, SSF, Dual WL, 1310nmTX 1550nmRX, AC 115V or 230V, DC – 48V

FiberMix 2504-120 Standalone, 4 E1 channels optical multiplexer, 4 10/100 RJ45, remote SNMP-management, SSF, Dual WL, 1550nmTX 1310nmRX, AC 115V or 230V, DC –48V

FiberMix 2401-30, FiberMix 2601-30 Module - PDH Fiber Optical Multiplexers - 1 single strand fiber optical port (Single mode 1310nm TX 1550nm RX and 1550nm TX 1310nm RX), 1 E1 port and 1 Fast-Ethernet port

FiberMix 2401-60, FiberMix 2601-60 Module- PDH Fiber Optical Multiplexers - 1 single strand fiber optical port (Single mode 1310nm TX 1550nm RX and 1550nm TX 1310nm RX), 2 E1 ports and 1 Fast-Ethernet port

FiberMix 3100-155 SDH Multi-Service multiplexer

If you need further information, please fill out this form below

What kind of information would you like to receive from us?

Please fill out the contact information:
First name/Last name: *
Company: *
E-mail: *
Your phone (country/city code): *

* Indicated a required field

DYNAMIX^®