DYNAMIX HP-53/M and DYNAMIX HP-53/M Outdoor - EoC Coax MDU Master Bridge (700/350Mbps)

DYNAMIX HP-53/M, DYNAMIX HP-53/M Outdoor

EoC Coax MDU Master Bridge (700/350Mbps)

Specification | Front panel | Back panel | Application | Ordering information

DYNAMIX HP-53/M

DYNAMIX HP-53/M Outdoor

   The EoC Coax MDU Master Bridge DYNAMIX HP-53/M or DYNAMIX HP-53/M Outdoor Enables You to Start the Triple-Play Services to a Small Scale Apartment Building.
   No Additional Network Wiring is Necessary. You may just Use the Existing Coax Wiring in the MDU Building, and be Ready to Provide Broadband Services to Subscribers.

   Low Initial Deployment Cost DYNAMIX HP- 53/M (DYNAMIX HP-53/M Outdoor) Compare to the High Cost xDSL Solutions, Suitable to Small Scale Building with Limited Subscribers. Supports IPv4 and IPv6 provide the flexibility for operators.
   Via the RJ-45 Ethernet Ports, Connect the MDU Master DYNAMIX HP- 53/M ((DYNAMIX HP-53/M Outdoor)) with Broadband Access Devices such as Fiber Media Converter and ADSL/Cable Modem. With DYNAMIX HP- 53/M (DYNAMIX HP-53/M Outdoor) high throughput and QoS, it can optimize IPTV service.

   Remote Management Function in DYNAMIX HP- 53/M (DYNAMIX HP-53/M Outdoor) Help to Ease the Support. The unique endpoint service control supports service providers with different service levels and service schemes.

User's manual
Mb

Quick start
Mb

•

Two models:
DYNAMIX HP-53/M - Coax MDU Indoor Master Bridge and
DYNAMIX HP-53/M Outdoor - Coax MDU Outdoor Waterproof Master Bridge

•

Design for Operators Providing High Speed Service over Coax Network

•

EoC up to 700/350 Mbps PHY/Throughput Rate as Distribution Backbone over Coax

•

Two 100/1000M Gigabit Ethernet Ports with One Port 100/1000Mbps SFP Support

•

Up to 90dB Attenuation on Coax Network

•

Support up to 253 Endpoints with Isolation

•

Line Power Feeding by Coax or PoE

•

IPv4 and IPv6 Support

•

Endpoint Service Control and Bandwidth Control

•

Endpoint Ethernet Loop Detection and Isolation

•

Online Diagnosis Support

•

802.1p QoS and 802.1Q Tag VLAN Support

•

IGMP Snooping Control

Networks standards
	EoC (Ethernet over Coaxial Cable)
	IEEE802.3ab 1000M Gigabit Ethernet
	IEEE802.3u - 100M Fast Ethernet
	IEEE 802.3az Energy Efficiency Ethernet

Connectors
	LAN : Two RJ-45 Connectors, One SFP Slot
	Coax: Two F-Type Female Coax Connectors, One for EoC, the Other for TV or Antenna - DYNAMIX HP-53/M
	Coax: 5/8” - 24 NEF, Four Diplexers Built-in, Two EoC Masters, Two Diplexers per Master (Two EoC Band splitters (Built-in) - DYNAMIX HP-53/M Outdoor

Modulation, TX Power and Spectrum
	OFDM, 15 +/- 1 dBm, 7.5–67.5MHz
	Filter: 76MHz

Transmission Speed and Range
	PHY/Throughput 700/350Mbps
	90dB Max Attenuation, High Speed within 50dB

Ethernet and Fiber Interface
	10/100/1000 Mbps, MDI/MDI-X Auto Crossover
	SFP interface: 100/1000Mbps, 3.3V TTL

Network Management
	Web, Telnet and SNMP Support
	Firmware Upgrade for Master and Endpoints
	DHCP Client, Option 82 and Snooping
	Auto Configuration/Provision Support
	IPv4 and IPv6 Dual Stack Support
	Priority Based on 802.1p, TOS, TCP/UDP Port
	802.1Q Tag VLAN Support
	Online Diagnosis of Coax Interface
	Bandwidth Control and Host Number Control
	IGMP v3 Snooping Control
	Endpoint Ethernet Statistics, Status, Loop Detection and Isolation

Reset Button
	Reset Device or Force to Factory Setting

Indicators
	“Power” LED, “Line Power” LED
	EoC “Link/Act”, “Quality”, “Diag” LED
	LAN “Link/Act” LED x 2

Power Requirement DYNAMIX HP-53/M
	External Power Supply : 12V DC
	Line Power Feeding from Coax I/F: 60VAC +/- 20%
	Line Power Feeding by IEEE802.3af PoE (37~57V)
	Switch to Select External Power or Line Power
	Power Consumption : < 5 Watts

Power Requirement DYNAMIX HP-53/M Outdoor
	Line Power Feeding from Coax I/F: 60VAC +/- 20%
	DC12V and DC5V Output for Powering Fiber Device (ONU/ONT or Media Converter)
	Power Consumption : < 8 Watts, < 20 Watts including DC12V/5V Output

Environmental Conditions
	Operating Temperature : -10 C ~ 55 C (14 F ~ 131 F) - DYNAMIX HP-53/M Operating Temperature : -30 C ~ 65 C (22F ~ 150F) - DYNAMIX HP-53/M Outdoor
	Storage Temperature : -10 C ~ 65 C (14 F ~ 149 F) - DYNAMIX HP-53/M Storage Temperature : -20 C ~ 70 C (4 F ~ 158 F) - DYNAMIX HP-53/M Outdoor
	Operating Humidity : 10% ~ 95%, Non-Condensing

Physical Dimension
	178mm (W) x 136mm (D) x 35mm (H) - DYNAMIX HP-53/M 223mm (W) x 195mm (D) x 105mm (H) -DYNAMIX HP-53/M Outdoor
	Weight: about 430g - DYNAMIX HP-53/M Weight: about 2500g - DYNAMIX HP-53/M Outdoor

DYNAMIX HP- 53/M	EoC Coax MDU Master Bridge (700/350Mbps), Indoor
DYNAMIX HP- 53/M Outdoor	EoC Coax MDU Master Bridge (700/350Mbps), Outdoor

Also see the products of this group:

EoC (Ethernet over Coaxial Cable)

DYNAMIX HP- 53/M EoC Coax MDU Master Bridge (700/350Mbps), Indoor

DYNAMIX HP- 53/M Outdoor EoC Coax MDU Master Bridge (700/350Mbps), Outdoor

DYNAMIX HP-53/S EoC Coax MDU Data Endpoint (700/350Mbps), 2 ports 10/100 Base-TX

DYNAMIX HP-53/SW EoC Coax MDU Endpoint with WiFi 11b/g/n (700/350Mbps), 2 ports 10/100 Base-TX

DYNAMIX HP-53/S FXS EoC Coax MDU Voice Endpoint (700/350Mbps), 2 ports 10/100 Base-TX, 1 port FXS

DYNAMIX HP-53/SW FXS EoC Coax MDU Voice Endpoint with WiFi 11b/g/n (700/350Mbps), 2 ports 10/100 Base-TX, 1 port FXS

HomePNA 3.1 adapter, router

DYNAMIX HP-30/S(FE) HomePNA 3.1 (192 Mbps) - Ethernet adapter (2 ports 10/100 Base-TX)

HomeCNA 3.1 Bridge, adapter

DYNAMIX HP-33/S(GE) HCNA (HomePNA 3.1 over Coax) to Gigabit Ethernet Bridge {256Mbps}

DYNAMIX HP- 52/M HomeCNA3.1 Coax MDU Master Bridge (2 ports 10/100/1000 Base-TX) (192Mbps)

DYNAMIX HP- 52/S HomeCNA3.1 Coax modem (2 ports 10/100 Base-TX) (192Mbps)

DYNAMIX HP- 52/S FXS HomeCNA3.1 Coax modem (2 ports 10/100 Base-TX) (192Mbps) with FXS port

DYNAMIX HP- 52/SW HomeCNA3.1 Coax modem (2 ports 10/100 Base-TX) (192Mbps) with WiFi 11b/g/n

DYNAMIX HP- 52/SW FXS HomeCNA3.1 Coax modem (2 ports 10/100 Base-TX) (192Mbps) with WiFi 11b/g/n and FXS port